How to Fix Christmas Lights

You just finished decorating your Christmas tree with ornaments and Christmas lights. Suddenly, you notice a few bulbs are burned out. No problem; you have several spare bulbs in a drawer that you saved just for this moment. Wait, these are old bulbs from several years ago and the base of the bulbs won't fit into the socket of the burned out lights. What now?

Remove the burned-out Christmas light bulb from its socket. Do this by carefully applying upward pressure on the plastic base just below the glass bulb. It helps to have fingernails when doing this. Try not to pull on the glass bulb.

Once the old bulb has been removed, compare its base with that of the replacement bulb. If it matches, then you should have no problem easily just inserting the new bulb into the socket. If the bases do not match, then you will need to remove both bulbs from their sockets and swap them.

You will probably need to straighten the wires so that they will fit into the holes of the socket.

To remove a Christmas light from its socket, find the two copper wires at the base of the bulb. Push both wires downward so that if the tip of the bulb is pointing at the ceiling, then the wires will point towards the floor. Firmly pull upward on the glass bulb and it should separate from the base. Do the same thing with the replacement bulb.

With both copper wires from the new bulb pointing straight down, insert the new bulb into the old bulb's socket and try to align the copper wires with the two holes at the bottom of the base. Once the wires have been inserted, press the bulb completely down into the base. Push both wires upward so that they follow the groove on each side of the bulb base. Now they should be facing the same direction as the tip of the glass bulb. Insert this new arrangement into the empty light socket and the bulb should illuminate!

Tips & Warnings

• Be careful when working with electricity! If possible, wrap a small piece of masking tape around the base of the burned-out bulbs to mark them and them perform the bulb replacement with the Christmas lights unplugged.

How to Make Christmas Lights Last Longer

Decorating for Christmas is always exciting, but who really enjoys stringing 3000 lights onto a Christmas tree only to have to remove them a month later? The next year you pull out the same strings of light bulbs and half of them don't work. There must be a better way!

Many Christmas trees are offered as "pre-lit" trees, but those weren't always available. For people with non-pre-lit trees who only enjoy stringing Christmas lights for the first ten minutes, this article should offer some encouraging suggestions. First buy one of the long green extension cords with outlets positioned every 12 inches or so. These should be available at your local home improvement store and are made specifically for plugging in Christmas lights. The very last plug should be positioned within about a foot from the top of the tree and the remainder of the cord should run down the center of the tree. You may want to wrap the cord around the center pole of the tree so that it will stay towards the center and not stand out.

If you will be using an angel that requires electricity on top of the tree, go ahead and situate her on top and plug her in. Now, begin at the top and work your way down wrapping each branch with several Christmas lights. Pull the lights out to the end of the branch and wrap towards the center. Leave several lights loose in the middle near the center. You will appreciate the effect once the entire tree is lit and you see that the lights appear to be scattered within the tree and not just on the outside portion of the branches. Use lots of lights! Don't worry about how long it may take to remove them later.

Now, here's the best part, when Christmas is over, leave all of the Christmas lights on the tree! Remove the delicate ornaments and the angel and wrap the tree carefully with a blanket. Pick up the tree, lights and all, and move it to your storage building. Stand the tree up for storage. The reason for leaving the lights on the tree is because removing them contributes to the reason why they don't work the very next year. Most strands of Christmas lights will work if several of the bulbs burn out, but the entire strand goes out if a single bulb is loosened or removed. By carefully wrapping the tree in a blanket and then storing it standing up, you are protecting the bulbs from unnecessary pressure and movement. They will last for years. If some of the bulbs burn out, they may be replaced or fixed.

Tips & Warnings

• Be very careful when moving the Christmas tree, not to bang it on the sides of a door or wall. That will completely defeat the purpose of leaving the lights on the tree and you will end up having to find which bulb is loose out of hundreds of them.